黄大仙精选资料二四六

双组份打胶机漏胶处理形式都有哪些?

发布时间:2020/01/04    发布人:

自动点胶机点胶阀泄漏
  Leakage of dispensing valve of automatic dispensing machine
  自动配胶机的胶阀常在胶阀关闭后发生泄漏,这种情况95%是由于使用的针径过小造成的。
  The rubber valve of the automatic dispensing machine often leaks after the rubber valve is closed. 95% of this situation is caused by the small diameter of the needle used.
  将调剂控制器的出风口通过风管连接到注射器上,将注射器气阀连接到调剂控制器的进气口上。
  Connect the air outlet of the dispensing controller to the syringe through the air pipe, and connect the syringe air valve to the air inlet of the dispensing controller.
  一般来说,混合管的长度和自动配料机的控制杆是用来确定胶水混合的程度和控制胶。混合管是静态混合的混合方法,它由一系列的左、右旋转叶片互相垂直排列在套管。当胶水A和B通过搅拌管时,进行连续切割,使混合均匀。混合管的出口可以连接到适配器上,方便使用任意口径的针,保证准确的出胶量。
  Generally speaking, the length of mixing pipe and the control rod of automatic batching machine are used to determine the mixing degree and control glue. The mixing tube is a static mixing method, which consists of a series of left and right rotating blades arranged vertically in the sleeve. When glue a and glue B pass through the mixing pipe, cut them continuously to make the mixing even. The outlet of the mixing tube can be connected to the adapter, which is convenient to use any caliber needle, and ensures accurate glue output.
  注射器放入注射器座内固定后,即可连接空气阀。将调剂控制器的出风口通过风管连接到注射器上,将注射器气阀连接到调剂控制器的进气口上。通过电缆将点胶机的“点胶”接口连接到点胶控制器的信号输入接口。踏板连接:将踏板连接到点药机“运行”界面,控制点药机的运行。z轴电缆连接:将z轴的连接电缆插头连接到点药机“z轴”上。

双组份打胶机
  After the syringe is fixed in the syringe base, the air valve can be connected. Connect the air outlet of the dispensing controller to the syringe through the air pipe, and connect the syringe air valve to the air inlet of the dispensing controller. Connect the "dispensing" interface of dispensing machine to the signal input interface of dispensing controller through cable. Pedal connection: connect the pedal to the "operation" interface of the dispensing machine to control the operation of the dispensing machine. Z-axis cable connection: connect the z-axis connecting cable plug to the "z-axis" of the dispensing machine.
  过小的针会影响液体的流动,造成反压,导致橡胶阀门关闭后不久出现液滴泄漏。过小的针也会影响到橡胶阀排气时气泡的运动,只要更换较大的针就可以解决这个问题。
  Too small needle will affect the flow of liquid, resulting in back pressure, resulting in liquid drop leakage shortly after the rubber valve is closed. Too small needle will also affect the movement of air bubbles when the rubber valve exhausts. As long as the larger needle is replaced, this problem can be solved.
  锥形锥形针产生最小的背压和最大的流体流量。
  The conical needle produces minimum back pressure and maximum fluid flow.
  当橡胶阀间隙完成时,空气中出现液滴现象,最好排除液滴空气,否则不易切换到含有泡泡糖的状态。或在离心式脱气后使用胶水。强力胶(快干胶)在橡胶阀门配件和管道中堵塞,这主要是由于水分过多或重复使用强力胶造成的。确保使用新鲜的即时胶水。管道在潮湿的丙酮中清洗干净。使用时应确定干燥空气和厂内空气压力,并在橡胶阀系统上加装过滤器。(如果以上方法仍然无效,则应使用氮气。)
  When the clearance of rubber valve is completed, the phenomenon of liquid drop appears in the air. It is better to eliminate the air drop, otherwise it is not easy to switch to the state containing bubble gum. Or use glue after centrifugal degassing. Strong glue (quick drying glue) is blocked in rubber valve fittings and pipes, which is mainly caused by excessive moisture or repeated use of strong glue. Make sure to use fresh instant glue. Clean the pipeline in humid acetone. Dry air and in plant air pressure shall be determined during use, and filter shall be installed on rubber valve system. (if the above method is still ineffective, nitrogen should be used. )
  需要注意的是,手持编程器是通过串行线选择到配药机左侧的接口上的。6. 如果使用的胶液点胶控制器与胶液点胶机的接头型号相同,则根据接头的芯数可以看到胶液点胶机的“点胶”和“操作”。两芯用于上胶,三芯用于操作。
  It should be noted that the hand-held programmer is selected to the interface on the left side of the dispensing machine through the serial line. 6. If the joint model of the glue dispensing controller used is the same as that of the glue dispensing machine, the "dispensing" and "operation" of the glue dispensing machine can be seen according to the number of cores of the joint. Two cores for gluing and three cores for operation.
  以上就是双组份打胶机对全自动封胶机漏胶的处理方式的详细介绍,想要了解更多请点击官网http://emikasarl.com
  The above is a detailed introduction to the handling method of the leakage of the full-automatic sealing machine by the two-component sealing machine. For more information, please click http://emikasarl.com