四川11选5

中空玻璃全自动封胶机的调试注意事项!

发布时间:2019/07/26    发布人:

中空玻璃全自动封胶机是玻璃深加工设备中产生较晚但用量较大的机械设备之一,主要作用是将半成品的中空玻璃做好密封,也可以作异形玻璃的密封。正确合理的使用中空玻璃自动打胶机,不仅能保证生产的正常进行,还会起到延长机器寿命的作用,下面小编就给大家讲一讲中空玻璃全自动封胶机的调试的方法和一些注意事项!
Hollow glass automatic sealant machine is one of the mechanical equipments which produce late but consume large amount in glass deep processing equipment. Its main function is to seal semi-finished hollow glass well, and also to seal special-shaped glass. Correct and reasonable use of hollow glass automatic gluing machine can not only ensure the normal production, but also play a role in prolonging the life of the machine.
调试方法:放在一个平整干净的平面上,连接电源和气源,两者确认接通之后就开始进行操作。首先打开气泵开关,电源总开关,控制台开关,在控制台按手动按钮,然后在显示屏上找到原点设定,点击辅助原点设定,然后点击头部原点设定,注意原点设定时避免头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定,先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度,输入完以后,点击设置进入。等命令位置和当前位置数值一致即可,注意设置时传送带上不要有玻璃。然后是混交了,按第一桶胶按钮,按工作选择按钮,然后按拍胶启动,在按伐开,此时胶头以出胶,等看不见白胶,以混均匀以后按伐关,在按链接生产线,自动,自动运行,此时可以自动打胶。
Debugging method: Put it on a flat and clean plane, connect the power supply and the gas source, and then start operation after the two are confirmed to be connected. Firstly, turn on the air pump switch, the main power switch, the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, then click the origin setting on the head, pay attention to avoid the collision between the head and the auxiliary sucker when setting the origin. After setting it, return to find the glass thickness setting, first the glass thickness, then the aluminium partition, then the glass thickness. After input, click Settings to enter. Just wait for the command position to be consistent with the current position value. Be careful not to have glass on the conveyor belt when setting. Then mixing, press the first bucket glue button, press the work selection button, then press the tap glue to start, in the cutting, at this time the glue head to produce glue, etc. can not see the white glue, after mixing evenly, press the cut off, in the link production line, automatic, automatic operation, at this time can automatically glue.

全自动封胶机
调试的注意事项:
Notes for debugging:
1、在当天机器操作完毕后要把胶管内的胶冲出,防止硬化;如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the machine is finished, the glue in the rubber tube should be washed out to prevent hardening. If it is not practical for a long time, we should pay attention to cleaning the rubber tube and gun with kerosene.
2、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高,低质量的胶容易堵塞胶管的过滤系统,造成出胶不畅或不均匀。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to block the filter system of rubber hose, resulting in poor or uneven glue production.
3、在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净,好清洗,因为不同品种甚至品牌的胶容易反应堵塞机器。
3. When replacing rubber varieties, special attention should be paid to cleaning the residual rubber in the two-component glue beater, because different varieties or even brands of glue are easy to react and clog the machine.
液压站系统的压力,不能调的太高,要根据室内环境温度等实际情况,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪,否则B组份管路压力将升得很高,造成安全事故。
The pressure of hydraulic station system can not be adjusted too high. According to the actual situation of indoor environment temperature, it can be adjusted to meet the normal tapping of rubber nozzles. When opening the hydraulic station, the rubber gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
以上关于全自动封胶机的一些基本情况就先给大家介绍到这里了如,如果大家还有什么不懂得的地方欢迎大家到我们的官网:http://www.emikasarl.com和我们的在线客服人员进行咨询,相信会给大家一个满意的答复。谢谢大家的支持!
四川11选5 The above basic information about automatic sealant machine will be introduced to you first. If you don't know anything else, you are welcome to our official website: http://www.emikasarl.com and our online customer service staff for consultation, I believe you will have a satisfactory answer. Thank you for your support!

四川11选5 四川11选5 四川11选5 四川11选5开奖结果 四川11选5 辽宁快乐12 博九 辽宁快乐12 四川11选5走势图 四川11选5走势图